How to lay artificial turf Kindergarten? |
How to lay artificial turf Kindergarten?
News Source:Wuxi Leisutan Artificial Turf Co.,Ltd -
1, check the entire site needs to lay turf, based on the density and flatness is to meet the requirements, you can begin paving after reaching the artificial turf.
2, before the start of paving artificial turf, the entire venue Surveying, measuring the position of the pitch line and make a mark, to determine the orientation and position of good laying artificial turf.
3, at the start of laying artificial turf: the joint surface of the pavement on the lawn with special stitching and fixed thereto with nails, nail head can not be raised, the transfer of lands required to coincide with 10 cm or more.
4, the glue coated on the joint interface, before the glue drying the tile and engage the lawn cut so close adhesion between each piece of the artificial turf.
5, after laying is completed, need to carefully check the adhesive bonding area is smooth, artificial grass is firmly bonded, after checking all meet the requirements before proceeding to the next step of construction.
6, in the need to insert into the white position cut green artificial turf artificial turf, then inserts into contact with, and on top coated with glue, then cut a good white artificial turf mark set in the pavement in front of a good pitch line Location and splicing tape be bonded.
7, according to the needs of the site and sprinkled with quartz sand particles. If you need to put the spilled quartz sand quartz sand or black rubber granules sprinkled into the machine, push spilled grains of quartz sand or machine can be filled with black rubber artificial turf surface, sprinkle grains brush flat rear of quartz sand or black particles, and to quartz sand or black rubber whereabouts sufficient.
8, pushing the speed granulator sprinkle evenly not too fast nor too slow, even to thickness.
9, quartz sand or rubber particles after laying flat and need to check whether sufficient deficiencies need to consider to fill, paving the need to immediately remove any impurities found in order to ensure quality.
10, paving the quartz sand or particles need to be kept dry in order to facilitate the flow of quartz sand or rubber granules pavement. Quartz sand or rubber granules after the completion of the pavement can also use a hard brush or light load drag-type heavy brush, brush laying back and forth so that the whereabouts of fully dense silica sand.
2, before the start of paving artificial turf, the entire venue Surveying, measuring the position of the pitch line and make a mark, to determine the orientation and position of good laying artificial turf.
3, at the start of laying artificial turf: the joint surface of the pavement on the lawn with special stitching and fixed thereto with nails, nail head can not be raised, the transfer of lands required to coincide with 10 cm or more.
4, the glue coated on the joint interface, before the glue drying the tile and engage the lawn cut so close adhesion between each piece of the artificial turf.
5, after laying is completed, need to carefully check the adhesive bonding area is smooth, artificial grass is firmly bonded, after checking all meet the requirements before proceeding to the next step of construction.
6, in the need to insert into the white position cut green artificial turf artificial turf, then inserts into contact with, and on top coated with glue, then cut a good white artificial turf mark set in the pavement in front of a good pitch line Location and splicing tape be bonded.
7, according to the needs of the site and sprinkled with quartz sand particles. If you need to put the spilled quartz sand quartz sand or black rubber granules sprinkled into the machine, push spilled grains of quartz sand or machine can be filled with black rubber artificial turf surface, sprinkle grains brush flat rear of quartz sand or black particles, and to quartz sand or black rubber whereabouts sufficient.
8, pushing the speed granulator sprinkle evenly not too fast nor too slow, even to thickness.
9, quartz sand or rubber particles after laying flat and need to check whether sufficient deficiencies need to consider to fill, paving the need to immediately remove any impurities found in order to ensure quality.
10, paving the quartz sand or particles need to be kept dry in order to facilitate the flow of quartz sand or rubber granules pavement. Quartz sand or rubber granules after the completion of the pavement can also use a hard brush or light load drag-type heavy brush, brush laying back and forth so that the whereabouts of fully dense silica sand.
Copyright © 2012 Wuxi Leisutan Artificial Turf
Co.,Ltd. All rights reserved